DIY & Woodworking

Build It Yourself.
Do It Right.

Plans, build logs, and no-BS guides for woodworkers and weekend builders. I figure it out so you don't have to.

Start here Browse Projects About Tom
Tiny House Loft Stair Calculator & Appendix AQ Math Guide

Tiny House Loft Stair Calculator & Appendix AQ Math Guide

Friday, February 27, 2026 Architecture , Building , Home Improvement , Stairs , Tiny Home ,
Diagram of IRC Appendix AQ tiny house loft stair dimensions including rise, run, and landing platform requirements
Key dimensions for Appendix AQ loft stairs: riser height (7"–12"), tread depth (7" min), stair width (20" below rail, 17" at rail), and the landing platform required when ceiling height is under 6’2".

If you’re building a tiny home with a loft and want to pull a permit, your stairs need to meet Appendix AQ of the International Residential Code. This is the section added specifically for tiny homes under 400 square feet. It relaxes the standard stair requirements — regular code would eat up too much floor space in a small build — but you still have to follow specific formulas for rise and run.

This post walks through how the math works and includes a calculator that handles all of it for you.

Read More →
How to Connect Two Submersible Pumps to a Single PVC Discharge Pipe

How to Connect Two Submersible Pumps to a Single PVC Discharge Pipe

Monday, October 09, 2023 Basement , How To , Plumbing ,

Dealing with occasional basement water issues? In this guide, I'll walk you through a straightforward DIY solution to connect two submersible pumps to a single PVC discharge pipe. This cost-effective project requires minimal tools and readily available materials from Home Depot or Amazon.

Why use PVC instead of a garden hose? PVC is stronger and available in wider diameters which will increase the flow rate of the pump. In the past I tried running a single pump through a garden hose but you get a lot less flow from a small garden hose than a larger pipe. I tried moving up to the black corrugated Everbuilt 1-1/4" Discharge Hose but that cracked the last time there was flooding so I wanted to connect my basement pump to a PVC pipe that should be more durable. I have two pumps just in case and at some point I will replace one with a 12V Utility pump on a backup battery.

Read More →
How to Make Your Airbnb WFH Friendly

How to Make Your Airbnb WFH Friendly

Tuesday, December 13, 2022 Decorating , Furniture , Interior , Network , Office , Tips ,

One way you can get more Airbnb bookings is if you attract more professionals to your Airbnb by making your rental more work-from-home friendly. In the past couple of years a lot of jobs went and stayed remote. Many people have been taking that opportunity to travel and see different cities and these guest tend to book longer stays which is very desirable. In this post I'll give you some tips and suggest products to make your Airbnb more attractive to guests that are planning to work from home.

I'm going to break down the WFH setup into 3 levels, Basic WFH, Advanced WFH and Video Conferencing WFH and within each of those levels, I'm going to suggest products that fit different budgets from low to high to cover different needs. Keep in mind I'm writing this at the end of 2022 which will affect the prices I mention.

You don't need to spend a lot for a WFH Airbnb setup but I would try to match the budget with the furnishings, area, and guests you are already targeting.
Read More →
3D Printed Nespresso Vertuo Pod Refill Holder

3D Printed Nespresso Vertuo Pod Refill Holder

Monday, April 25, 2022 3D Printing , Kitchen , Video ,
If you have Nespresso Vertuo coffee maker you can save a lot of money by refilling the pods yourself. You just cut off the old foil top and use new foil tops after It's a little cumbersome because the pods are round on the bottom and it can be difficult to align the foil top so I designed this Nespresso Pod Refill Holder that can be 3D printed to make refiling Nespresso Vertuo Pods easier.

My 3D Printed Nespresso Vertuo Pod Refill Holder will hold up to 2 Nespresso Vertuo pods. It is small and compact for easy storage.  I have a video showing how to use it and links to where you can download the .stl files to 3D print your own.

Read More →
Hand Washing On-The-Go Without Sanitizer

Hand Washing On-The-Go Without Sanitizer

Wednesday, April 01, 2020 Camping , How To , Tips , Video ,
In this post I share tips on how I wash my hands away from home without hand sanitizer.

The Corona Virus Pandemic has created a shortage on certain items including hand sanitizer. Even hand soap is difficult to find sometimes. At home I use some foaming hand soap dispensers because they make a significant savings in the amount of soap I use. I use a similar concept when away from home.

Disclaimer

I use this method when I don't have access to running water like if I'm out hiking or camping. Hand sanitizer is good for some things but not great for getting dirt off my hands if I want to clean my hands before eating. I don't have any way to verify how effective this is but it has worked well on dirt and the principles seem sound. With the shortage of hand sanitizer and gloves we need options. This is mine. If this is your only option to wash your hands continue to try to keep your hands away from your face to be safe.

What You'll Need

Step 1: Prepare Soap Solution

If you're using the foaming dispensers follow the instructions. If you're using a spray bottle, I use about a 1 to 4 or 5 ratio of liquid hand soap to water. After mixing I'll test it by spraying it on my hands. I'm looking for a small amount of thin lather. If there isn't enough slipperiness or lather I'll add a little more soap. If my hands get too foamed up I'll add more water.

Step 2: Prepare the Bleach Rinse Solution

I like to add some bleach to the rinse water to help it stay sanitary as well as for it to have some sanitizing effect. Since the FDA recommends a bleach dilution of 50-200 ppm for food contact surfaces including utensils, it seemed like a safe concentration to use on your hands. I wouldn't recommend going above 200ppm but during the ebola virus the CDC put out a document on how to create a bleach hand sanitizing solution that was about 500 ppm bleach.

Try to get bleach that has the concentration of bleach (sodium hypochlorate) listed on the label. If it's not on the label it's at most 3% but I'm not sure if it could be less than that. Use this bleach concentration calculator to help you determine the amount of your bleach you need to add to your bottle. Make a new solution every day. Try not to make too much more than you need. Use the calculator below to determine how much bleach you need.

Bleach Concentration Calculator

Enter the concentration of bleach found on the bottle, the concentration of finished solution you'd like in parts per million (ppm) and the total amount of sanitizer solution you'd like to end up with in ounces.

% bleach concentration
Desired concentration in ppm (50 to 100)
Total volume in ounces
Bleach Needed (use most appropriate measure)
ounces of bleach or
milliliters of bleach or
teaspoons of bleach

Step 3: Spray your hands

Spray your hands or pump out enough foam to start washing your hands. You should have a nice thin lather all over your hands. Rub them strongly together making sure you cover all areas thoroughly. Scrape your nails on your palms, scrub the back of your hands and fingers. Really scrub good.

Step 4: Rinse away soap

If you have access to clean running water use that to rinse your hands. If not use the spray bottle with bleach solution in it. Set the stream to a strong stream and spray the soap off your hands. Aim the spray so it doesn't splash back at you or anyone else.

Step 5: Dry your hands

Let the bleach solution stay on your hands for about a minute to sanitize them. You can let your hands air dry if that's your only choice but it's best to use a clean, dry, paper towel to dry your hands, especially since this method of rinsing isn't as effective as using running water.

How are you washing your hands?

This is what I'm doing. Let me know in the comments what you're doing or if you have any thoughts on my method. What else are you doing to keep safe?
Read More →
Freestanding Closet DIY Plans

Freestanding Closet DIY Plans

Wednesday, January 01, 2020 Bedroom , Cabinets , Closet , Easy , Plans , Projects , Woodworking ,
Free woodworking plans to build a freestanding or walk-in closet organizer.

About the Freestanding Closet Organizer

There are a lot of situations where you need additional closet space in a room. Older homes don't have large closets and some bedrooms may not have any closets at all if you're converting a den or study into a bedroom. This freestanding closet organizer provides ample room for hanging clothing, shelf space as well as 2 large drawers. It only needs 3 full sheets of 3/4" plywood and partial sheets of 1/2" and 1/4" to construct making it very affordable for the amount of storage you get.

Four of these Amazon Basics Fabric Storage Bins fit nicely on the top.

You can choose the plywood veneer and finishing option that best fits your decor.

Dimensions

When fully assembled the freestanding closet will be 74-1/4" wide by 23-15/16" deep by 85" high. If you'd like to make it narrower you can cut the shelves smaller.

What You'll Need

Materials

Tools

Cut List

  • (4) 85” 23-15/16” 3/4” Plywood Sides
  • (7) 23-3/4” 23-3/16” 3/4” Plywood Shelf
  • (8) 4-1/2” 23-3/4” 3/4” Plywood Stretcher
  • (2) 3-1/2” 23-3/4” 3/4” Plywood Toe Kick
  • (2) 10-7/8” 23-5/8” 3/4” Plywood Drawer Front
  • (4) 20” 10” 1/2” Plywood Drawer Box Side
  • (4) 21-3/4” 10” 1/2” Plywood Drawer Box F/B
  • (2) 22-1/4” 19” 1/4” Plywood Drawer Bottom

Cut Plan

3/4" Plywood

1/2" Plywood

1/4" Plywood

Step 1

Start by drilling all the pocket holes in the shelf, stretcher and toe kick plywood pieces as shown.

Step 2

Use wood glue and 1-1/4" Kreg pocket screws to attach the shelves to the stretchers. There will be 1 left over stretcher so don't worry. 2 of the shelves should have the pocket holes facing up while the others have the pocket holes facing down as shown.

Step 3

Apply edgebanding to the fronts of the shelves, fronts of sides, drawer fronts.

Step 4

Attach the shelves and toe kick to 2 of the side pieces to form the first freestanding closet cabinet using wood glue and 1-1/4" Kreg screws

Step 5

Attach the shelves to the 2 remaining side pieces to form the other fresstanding closet cabinet using wood glue and 1-1/4" Kreg screws.

Step 6

Build the 2 drawer boxes for the closet system as shown using wood glue and 1" Kreg Pocket Screws. For detailed instructions please read my post on how to build drawer boxes. 

Step 7

Mount the drawer boxes into the closet frame using the drawer glides.

Step 8

Attach the drawer fronts to the drawer boxes. There should be a 1/16" gap. I start by removing the bottom drawer box from the cabinet. I'll place the drawer front on the drawer box and position it where it looks good. You can use shims but eyeballing it is usually good enough. Then I'll pull out the drawerbox while pressing the front tight against the drawer box so it doesn't move as I pull it out. Now I can reach in and screw it in place temporarily using 1" screws. Then I'll drill holes for the drawer pulls and attach them.

Step 9

Notch out the back to fit around your baseboards. If your baseboards are taller than 3-1/2" you may need to make the toe kick higher.

Step 10

To finish things off place one of the cabinets on the wall where you want your freestanding closet system. Shim it so it's level and screw it through the stretchers into the wall framing to secure it.

Attach the middle shelves to the first cabinet using glue 1-1/4" pocket screws making sure everything is level and screw into the wall framing through the stretchers as well.

Place and attach the last cabinet attaching it to the middle shelves using pocket screws and glue. Use screws to attach the cabinet to the wall using screws into the wall framing.

Finally install the closet rod hardware so it's 2" down from the top shelf. 


Read More →